---
title: "Record a monetary risk estimate"
description: "Enter frequency and loss magnitude assumptions and inspect conversion status."
url: https://helpcenter.complytrain.net/en/articles/142-record-a-monetary-risk-estimate
collection: "Exposure, money and reports"
updated: 2026-09-22
language: en
---

# Record a monetary risk estimate

Enter frequency and loss magnitude assumptions and inspect conversion status.

Enter frequency and loss magnitude assumptions and inspect conversion status.

## Enter the estimate

Product location: `/rms/risks/{riskId}` (fallback: `/rms/risks`). Open the intended risk and the panel described below.

Open a risk's **Risk in money** section and choose before-controls or after-controls figures. Select **Estimate this** or **Revise**.

Enter the fewest, most likely and greatest expected loss-event frequency per year. Fractions are supported: 0.1 describes approximately one event in ten years. Keep the three values ordered from smallest to largest.

Choose a cost estimate from the loss-scenario library or enter the lowest, most likely and highest cost with its currency. Enter all three local cost values or leave all three empty to use the library estimate. Local values override the selected library estimate for this risk.

![The synthetic example enters annual frequency 0.1 / 0.3 / 1 and cost EUR 1,000 / 3,000 / 10,000, with an explicitly illustrative explanation.](https://staticfiles.gleap.io/p6950dfbf97796f2087a9f022/IVCb3LKoKhulpcrDdmqAjK7r9nhzUAhzuHCaPJrn3VLz3OsQwoRzZFvGHNPWsdUl1BTdf5U7n4L.png "Record the basis for a monetary estimate")![The saved example displays EUR 1,469 a year before controls. There is no after-controls estimate and no linked control evidence; no reduction is credited.](https://staticfiles.gleap.io/p6950dfbf97796f2087a9f022/YWuzIBJfLZ85KmEdq8G8dX7BD0UEeWzW99Ig1ZdZpxRxObXZN0ec2tvODJa1zFD116RzvpHfOJX.png "Inspect the saved estimate and missing control evidence")

## Explain the assumptions

Product location: `/rms/risks/{riskId}` (fallback: `/rms/risks`). Open the intended risk and the panel described below.

Use **Why these numbers** to record the basis, scope and limitations. Check a retired-library-estimate message before continuing to rely on its figures. Save and inspect the resulting estimate and plausible range.

If the inputs changed, **Total pending** means the calculation has not caught up. A missing exchange rate prevents conversion; an absent figure is not zero loss.

## Maintain shared inputs

Product location: `/rms/settings/loss-scenarios`

Use RMS Settings for loss scenarios and reporting currency. Review the currency and rate shown beside converted figures. Reusing a library estimate makes common assumptions easier to maintain, but confirm that its event and scope match the risk.

![The default is EUR until the organisation chooses a reporting currency. Rates are maintained separately.](https://staticfiles.gleap.io/p6950dfbf97796f2087a9f022/dDs5HOFuJwUSRBtAro7a11hJNSuqJgwUfWPTx7WrLbmnnru2eqiYhK1fW9nO7HyE0qSjgmNSxUP.png "Inspect reporting currency and conversion")![Record a code, event, currency, three cost estimates and their basis before saving.](https://staticfiles.gleap.io/p6950dfbf97796f2087a9f022/HWtLcEpIzMK8U5lfZpyAEp0oxfXHocJ7KgxKaW5oKcZgZmlQ2hP3hejGJR11iH3dCgwE2uRrRxK.png "Prepare a reusable loss scenario")

## Loss-scenario field reference

Product location: `/rms/settings/loss-scenarios`

In **Loss scenario library**, select **Add a scenario**. Enter a stable code, loss-event description, optional group and original currency. Record **Cheapest**, **Most likely cost** and **Most expensive** in ascending order. Explain **Where these numbers came from**.

Expected cost weights the most likely value four times as heavily as either end. The result depends on your inputs; it does not validate the event or range. Check the calculation before saving and retain its basis.

The library lists each scenario's range, expected cost, how many risks use it and when it was last reviewed. Use **Revise** to update a scenario. **Still current** records that you reviewed the figures and they still hold. The library flags estimates that have not been reviewed for over a year.

**Retire** takes a scenario out of use for new estimates, and **Bring back** restores it. Use **Show retired scenarios** when investigating an older risk's assumptions. Retiring a library entry does not mean the historical estimate was never used.

## Currency and conversion reference

Product location: `/rms/settings/currency`

In **Reporting currency**, choose the common currency, conversion policy and decimal places. Until configured, the interface displays EUR and a reminder.

<table style="min-width: 50px;"><colgroup><col style="min-width: 25px;"><col style="min-width: 25px;"></colgroup><tbody><tr><th colspan="1" rowspan="1"><p>Setting</p></th><th colspan="1" rowspan="1"><p>Choices</p></th></tr><tr><td colspan="1" rowspan="1"><p>Reporting currency</p></td><td colspan="1" rowspan="1"><p>The three-letter currency code for all totals, such as EUR or USD.</p></td></tr><tr><td colspan="1" rowspan="1"><p>How to convert other currencies</p></td><td colspan="1" rowspan="1"><p><strong>At the rate on the record's own date</strong> (default), <strong>At the newest rate on file</strong>, or <strong>Do not convert</strong>.</p></td></tr><tr><td colspan="1" rowspan="1"><p>Decimal places</p></td><td colspan="1" rowspan="1"><p>0–6 (default 0).</p></td></tr></tbody></table>

Changing the reporting currency re-values the whole register. The page tells you how many stored totals will be recalculated.

Under **Exchange rates**, choose **Add a rate** and enter **From**, **To**, **Rate**, **In force from** and an optional **Source**, then **Save the rate**. A rate for the same currency pair and date replaces the earlier one. Rates are supplied by your organisation, not a live market feed.
